If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology. ASRock i65G Motherboard 11 2. Collegare il LED di accensione chassi per indicare lo stato di alimentazione del sistema. ASRock i65G Motherboard 15 2. ASRock i65G Motherboard 19 3. Do NOT place jumper caps over these headers and connectors.

Uploader: Yokazahn
Date Added: 16 November 2012
File Size: 42.36 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 33026
Price: Free* [*Free Regsitration Required]

Also remember to use a grounded wrist strap intek touch a safety grounded object before you handle components. Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. NO coloque las cubiertas de los puentes sobre estos cabezales y conectores. Align fasteners with the motherboard throughholes. Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components.

To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. English Please refer to the warning on page 7 for the possible overclocking sudio before you apply Untied Overclocking Technology.

Repeat with remaining fasteners. Therefore, the drivers you install can work properly. Although this motherboard offers stepless control, it is not recommended to perform over-clocking.

NAO ligue as placas maes i65G!


ASRock > DualPro

Andernfalls reicht der Strom nicht aus, das System zu starten. Before you installed the heatsink, you need to spray chamnel interface material between the CPU and the heatsink to improve heat dissipation. Obwohl dieses Motherboard stufenlose Steuerung bietet, wird Overclocking nicht empfohlen. Replace the system cover.

ASRock > i65G R

More detailed information of the motherboard can be found in the user manual presented in the Support CD. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages including damages chxnnel loss of profits, loss channnel business, loss of data, interruption of business and the likeeven if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

Web site da ASRock: Jumper Setting JR1 ver p.

The current SATA interface allows up to 1. Remove the system unit cover if your motherboard is already installed in a chassis. No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Si los puentes JL1 y JR1 son cortos, tanto el conector de audio del panel frontal como del panel posterior pueden funcionar.


This cap must be placed if returning the motherboard for after service. Keep the screws for later use. While pressing down lightly on load plate, engage the load ontel. While CPU overheat is detected, the system will automatically shutdown. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Fate riferimento alle dua, del produttore del dispositivo IDE per maggiori dettagli.

ASRock 775I65G – motherboard – micro ATX – LGA775 Socket – i865G

Rotate the load lever to fully open position at approximately degrees. Faute de quoi, il ne sera pas possible de mettre sous tension. Es geschieht dann auf eigene Gefahr und auf Ihre Kosten. Rotate the load plate onto the IHS. This motherboard supports Untied Overclocking Technology.

Carefully place the CPU into the socket by using a purely vertical motion. Ligue o cabo do ventilador neste conector, coincidindo o fio preto com o pino de aterramento. If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.