AC parameters are guaranteed by design and characterization. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. They should not introduce major impedance discontinuities. AC specifications for the driver are a tenfold improvement over other existing RS drivers. This component has a RoHS exemption for either 1 lead-based flip-chip solder bumps used between the die and package, or 2 lead-based die adhesive used between the die and leadframe. National Semiconductor Corporation Americas Tel:
|Date Added:||1 January 2009|
|File Size:||57.79 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
They are not meant to imply that the devices should be operated at these limits. The common-mode bias point should be set to approximately 1. AC or unterminated configurations are not allowed.
TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Other configurations are possible such as a multireceiver configuration, but the effects of a mid-stream connector scable stub sand other impedance discontinuities as well as ground shifting, noise margin limits, and total termination loading must be taken into account. Shorted input fail-safe is not supported across the common-mode range of the device GND to 2.
Termination Use a resistor which best matches the differential impedance of your transmission line. Twisted pair cable will offer better balance than flat ribbon cable.
Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result ilne a significant injury to the user.
3 V, LVDS, Quad, CMOS Differential Line Driver ADN4665
Math HW 9. The active high and active low enable inputs deactivate all the current drivers when the drivers are in the disabled state.
Generator waveform for all tests unless otherwise specified: Documents Flashcards Grammar checker. The DS90LV differential line driver is a balanced current source design. This component has a RoHS exemption for either 1 lead-based flip-chip solder bumps used between the die and package, or 2 lead-based die adhesive used between the die and leadframe.
Generator waveform for all tests unless otherwise specified: National Semiconductor Europe Fax: All input voltages are for one channel unless otherwise specified. Pin Function Descriptions Pin No. They are not meant to imply that the devices should be operated at these limits. National Semiconductor Europe Fax: If the driver is in a TRI-STATE condition, or if the driver is in a power-off condition, or if the driver is even disconnected cable unpluggedthe receiver output will again be in a high state, even with the end of cable X termination resistor across the input pins.
DS90LV 3V LVDS Quad CMOS Differential Line Receiver
Nonetheless, such components are subject to these terms. If a line is indented then it is a continuation of the previous line and the two combined represent cos entire Dufferential Marking for that device. Channel 4 Inverting Output Current Driver. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI.
The current mode driver provides substantial benefits over voltage mode drivers, such as an RS driver.
DS90LVAQML 3V LVDS Quad CMOS Differential Line Driver
The unplugged cable can become a floating antenna which vlds pick up noise. TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
This specification applies to devices over the recommended operating temperature and voltage ranges, and across process distribution. This part can be operated from 3. This internal circuitry will ensure a HIGH, stable output state for open inputs.
DS90LV031AQML 3V LVDS Quad CMOS Differential Line Driver
For ensured specifications and test conditions, see the Electrical Characteristics. Therefore, the noninverting receiver input is typically lvss. If EN is held high, EN enables the drivers when low or open circuit and disables the drivers and powers down the device when high.
AC or unterminated configurations are not allowed.